PEECO Flow Switches
Electrical Data
Meeting electrical requirements is a matter of correct micro-switch selection. PEECO uses premium, large snap-action switches with precise operating characteristics and enhanced service life.
Standard & Optional SPDT Micro-Switch Options
PEECO uses premium large snap-action switches. The standard SPDT is included with every unit; optional configurations are available for specialized applications.
SPDT Micro-Switch
The standard switch supplied with every PEECO flow switch. A large snap-action SPDT micro-switch with precise operating characteristics and long service life. Provides one normally open, one normally closed, and one common terminal.
15A · 125–250–480 VAC · 1-N.O. · 1-N.C. · 1-Comm.
Stacked SPDT Micro-Switches
Two or more SPDT micro-switches stacked on a single actuator for applications requiring multiple independent switching circuits — alarm, shutdown, and control — all triggered at the same flow set point. Available in 2, 3, or 4 switch configurations.
(2), (3), or (4) Micro-Switches · STD 15A · 480 VAC
Bi-Directional SPDT
Two SPDT micro-switches configured for bi-directional flow detection. One switch actuates on forward flow, the other on reverse flow — ideal for processes where backflow must be detected and alarmed independently from normal forward flow conditions.
(2) SPDT · Forward & Reverse Flow · Independent Circuits
Hermetically Sealed Switches
Designed for applications where maximum electrical rating and maximum sealing are essential. Sealed per MIL-S-8805, design symbol 5 (–67° to +180°F or –55° to 82°C). Constructed to military standard specifications.
(2) Micro-Switches (STD 15A. 480 VAC)
(3) Micro-Switches (STD 15A. 480 VAC)
(4) Micro-Switches (STD 15A. 480 VAC)
(2) SPDT micro-switches stacked for sensitivity
Standard SPDT Specifications
| Circuitry | SPDT |
| Termination | Screw |
| Actuator | Overtravel plunger |
| Voltage | 125 Vac, 250 Vac, 125 Vdc, 250 Vdc |
| Housing | General purpose phenolic |
| Dielectric strength | 2000 V between each terminal and ground |
| Contact resistance | 15 m Ohm max. (initial) |
| Insulation resistance | 100 M Ohm min. |
| Expected mechanical life | Up to 20,000,000 cycles at 95% survival |
| Expected electrical service life | 100K operations at rated load |
| Rated frequency | 50 Hz / 60 Hz |
Additional Switch Options
10A 125 Vdc SPDT (optional)
5A 480 Vac 400°F SPDT (optional)
15A 600 Vac SPDT (optional)
10A 125 Vac DPDT (optional)
5A 125 Vac SPDT Hermetically sealed (optional)
1A 125 Vac SPDT Hermetically sealed (optional)
ENEC and CE recognized. Over 75 years of engineering excellence. Industry-leading temperature range: up to 204°C [400°F] and as low as –55°C [–67°F].
Multiple Action
DPDT Option
Air Operated
Dash-Pot
TopWorks Options
Configuration options for the switch assembly mounted atop the PEECO flow switch body.
Multiple Action
Flow / Reverse Flow
By special use of two or more (up to 6) micro-switches, indicates combinations such as flow/no-flow, two different flow actuation points, or flow/reverse flow.
DPDT Option
Dual Circuit Switching
Two SPDT micro-switches stacked to provide DPDT function. Available for applications requiring dual-circuit switching.
Air Operated
No Electrical Contacts
Where electrical contacts are not permitted or where pneumatic operation is preferred. Supply pressure: 3 to 20 psi or 20 to 125 psi.
Dash-Pot Option
For Turbulent Flows
Delays switch action up to 30 seconds to avoid false actuation due to cavitation or turbulent flow conditions.
Electrician's Reference — NO · NC · Common Connections
Every SPDT micro-switch has three terminals. Understanding how they behave — and how qualified electricians wire them — is essential for correct installation.
Common (C)
The shared terminal — always connected to either NO or NC depending on paddle position. The incoming power supply or signal wire is typically landed here.
The line-side conductor (hot wire or control voltage) is connected to Common. This makes Common the reference point from which the switch routes current to either the NO or NC terminal.
Normally Open (NO)
Open (no continuity) when the paddle is at rest — no flow. Closes (completes the circuit) when flow actuates the paddle.
The load — pump motor starter, solenoid valve, PLC input, or alarm relay — is wired to NO when the device should energize on flow. This is the most common wiring configuration for flow-proving applications.
Normally Closed (NC)
Closed (continuous circuit) when the paddle is at rest — no flow. Opens (breaks the circuit) when flow actuates the paddle.
The load is wired to NC when the device should de-energize on flow, or when a loss-of-flow alarm is needed — the circuit stays energized during normal no-flow conditions and opens the moment flow is detected.
Important: All wiring of PEECO flow switches must be performed by a qualified licensed electrician in accordance with the National Electrical Code (NEC), applicable local codes, and the installation instructions supplied with the unit. In hazardous locations, wiring methods must also comply with NEC Article 501 for Class I Division 1 installations.
Understanding Micro-Switch Terminology
A plain-language guide to the switch types and wiring connections used in PEECO flow switches — for engineers, electricians, and anyone specifying or installing a unit in the field.
SPDT
Single Pole Double Throw
The standard micro-switch supplied with every PEECO flow switch. A single switching element — one pole — that can connect to either of two output circuits depending on whether the paddle is actuated or at rest. Simple, reliable, and the right choice for the vast majority of flow detection applications.
DPDT
Double Pole Double Throw
Two independent SPDT switching elements — two poles — operated simultaneously by the same actuator. Each pole has its own set of NO, NC, and Common terminals, giving you two completely isolated switching circuits from a single actuation point.
Hermetic
Hermetically Sealed
A micro-switch whose internal contact mechanism is completely sealed inside a welded metal enclosure — no air, moisture, or contaminants can reach the contacts. Required in environments where corrosive gases, high humidity, or explosive atmospheres could degrade or ignite an unsealed switch.
Related PEECO Pages
Need Help Selecting the Right Switch?
Our engineering team will help you select the correct micro-switch configuration for your application.
1-201-419-6111 · [email protected]
Quick RFQ
Request Pricing